1. TOP
  2. TOP
  3. Application
  4. Measuring example from each industry
  5. Automobile and Motorcycle

Automobile and Motorcycle

Application in Automobile and Motorcycle industry

Measurement of piston behavior

Measurement of piston behavior

Measure piston behavior(piston slap) by setting GAP-SENSOR in piston skirt and measuring a gap from a cylinder bore.
If provide fitting hole for setting the sensor, we offer setting the sensor. Setting thermocouple near the sensor is useful for measuring temperature and correcting temperature drift.(We offer set temperature drift)

Detail of relevant products

Measurement of a gap from connecting rod bearing

Measurement of a gap from connecting rod bearing

Measure a trajectory of the center of an axis by setting a sensor in bearing of connecting rod and measuring a gap from crank pin.
Consult with us to select size of the sensor by depending on the connecting rod. In case choosing PU-03A type and the size of a fitting hole is φ6, measuring range is 0 ~500μm.

Detail of relevant products

Measurement of a gap from crankshaft ②

Measurement of a gap from crankshaft ②

Measure behavior of crank journal by setting a thin sensor in the main bearing of the crank journal.
As a fitting hole depends on size of a main bearing, consult with us.

Detail of relevant products

Measurement of valve lift ①

Measurement of valve lift ①

Measure valve lift without processing valve, so weight of the valve does not change.
However, firing operation can not be conducted because of setting sensor inside combustion chamber.

Detail of relevant products

Measurement of valve lift ③

Measurement of valve lift ③

Measure several valve lift at the same time by setting sensors in several valve guide.
A small sensor can measure it by performing taper machining in a part of valve system when firing.

Detail of relevant products

Displacement measurement of a gasket

Displacement measurement of a gasket

Measure gaps or displacement between a gasket and cylinder head or cylinder block by setting a thin sensor in a cylinder gasket.
Consult with us to select size of the sensors depending on thickness of gasket.
*Thickness of gasket needs more than 1.2mm.

Detail of relevant products

Measurement of wheel balance

Measurement of wheel balance

Measure balance of wheel by setting sensor near targeted wheel.
Consult with us to select size of the sensor according to measuring points.

Detail of relevant products

Vibration measurement of a pulley and belt

Vibration measurement of a pulley and belt

Measure vibration of a pulley and belt by setting a sensor near the pulley and belt of automatic CVT type.
Consult with us to select a sensor according to vibration amount.

Detail of relevant products

Displacement measurement of a piston ring

Dosplacement measurement of a piston ring

Measure behavior of piston ring(up and down motion) by setting a sensor in piston land(piston ring side).
Consult with us to select size of the sensor according to size of the piston.

Detail of relevant products

Gap measurement of a crank shaft①

Gap measurement of a crank shaft①

Measure behavior of a crank journal by setting sensor in the main bearing of the crank journal.
Consult with us as a fitting hole is different according to the size of the crank journal.

Detail of relevant products

Rotation measurement of a turbine and compressor

Rotation measurement of a turbin and compressor

Measure rotation speed by setting a sensor against blades of turbine or compressor.
Moreover, the sensor can measure shaft vibration by setting it against the shaft.
We select a sensor according to a gap and size of a turbine. Consult with us as we have countermeasure products for operating temperature and frequency characteristics that is over the specification. 

Detail of relevant products

Measurement of valve lift ② 

Measurement of valve lift ②

Measure several valve lift at the same time by setting sensor inside combustion chamber.
A target pin needs to be set on a target in this measurement method, but it allows a small sensor to measure long stroke that conventional sensors cannot measure.
Moreover, the sensors can be used even in oil.

Detail of relevant products

Runout measurement of a brake disk rotor

Runout measurement of a brake disk rotor

Measure runout of rotation by setting a sensor against surface of the brake disk.
Consult with us as we have countermeasure products for higher operating temperature than the specification. 

Detail of relevant products

Measuring example by using a slip ring

Measuring example by using a slip ring

Measure behavior(up and down motion) of a piston ring by setting a sensor in piston land(ring side).
Generally, extracting an output by using slip ring cause a noise problem, but this type resolve the noise problem.

Detail of relevant products

Contact and Catalog Download are below

We deal with even one sensor. Moreover, we offer sensor calibration with measuring material, lending our product for a demonstration and so on.
Contact us about special order or customizing here

Question or Inquiry

Catalog Download are below